+49 (451) 703 64 997

LABOM 2 صفحة –

بيع أي منتج من كتالوج LABOM بأسعار جيدة

شركتنا ليست مُصنِّعًا أو موزعًا معتمدًا أو ممثلًا معتمدًا لعلامة LABOM التجارية في المملكة العربية السعودية. العلامات التجارية الخاصة وأرقام المقالات المعروضة على هذا الموقع هي ملك لأصحابها المعنيين.

LABOM 2 صفحة –

بيع أي منتج من كتالوج LABOM بأسعار جيدة

رمز البائع

description

السعر

CV3110-A1059-F80-H1100-M1-Y4-N51-T6-T31-K1085-W4020-W2002 DL9016-HY-E1-G1-A400-L22

CV3110 PRESSURE TRANSMITTER PASCAL CV, for diaphragm seal operation, hygienic acc. to data sheet D4-017/22 A1 pressure sensor: piezoresistive for gauge pressure 059 nominal range: 0...16 bar, overload limit 60 bar measuring range setting: turndown 5:1 accuracy: <= 0.15% of measuring span (linearity, hysteresis and repeatability) F80 measuring range: setting see below lower range value: - 1,000 upper range value: + 15,000 unit: bar H11 output signal: 4...20 mA, rising characteristic (standard) 0 setting damping: 0.0 sec. (standard) 0 setting alarm state: < 3.6 mA (standard) M1 display module: without Y4 screw cap with window mat. Macrolon N5 switching module: with 2 floating channels, pluggable, electrically isolated at all sides, switching capacity 30 V DC / 0.5 A 1 switching module setting: at the factory, see below 1. switch contact: switch point: 8 bar breaker hysteresis:0,1% (falling) 2. switch contact: switch point: 10 bar breaker hysteresis:0,1% (falling) T6 case: hygienic design with screw cap material: stainless steel degree of protection: IP 66 incl, vent filter, stainless steel T31 electrical connection: circular connector M 12x1 (8 pin) K1085 design standard W4020 ADDITIONAL DESIGN: marking (adhesive label), see below W2002 CALIBRATION PROTOCOL: with 5 measuring points DL9 DIAPHRAGM SEAL for food/pharmaceutical/biotechnology 016 design: APV flange design HY hygienic design per EHEDG Doc.8 and ASME BPE SF3: surface roughness (wetted parts) - turned parts Ra <= 0.76 μm - diaphragm Ra <= 0.38 μm - weld seam Ra <= 0.76 μm E1 basic body material: stainless steel (316L) G1 diaphragm material: stainless steel (316L) A400 connection of meas. instrument directly welded L22 system filling: Synthetic oil, free of silicon FD1 acc. to FDA 21 CFR 178.3570 / H1-registered operating temperature range -10...+140 °C spare parts for fab.-no.: 1819962/10/003

تحت الطلب

أحصل على سعر

CC6020-A1093-H1-T110-W4999-W2675

DE1180-A4001-L23-T99-W4999 PRESSURE TRANSMITTER COMPACT for diaphragm seal operation design: with temperature decoupler see data sheet D4-020-7 explosion protection: without pressure sensor piezoresistive for gauge pressure measuring range -1...24 bar, overload limit 60 bar measuring accuracy: linearity error incl. hysteresis < + 0.2 % f.s. accuracy of adjustment < +/- 0.2 % f.s. output signal: 4...20 mA, 2-wire technology electrical connection: right angle plug acc. to DIN EN 175301-803-A (DIN 43650, model A) IP 65, for cable ø 4...10 mm ADDITIONAL DESIGN: see below Design for process temperatures up to 205 ° C - EAC-TR certification exemption statement - metrological certificate for the use in Russian Federation DIAPHRAGM SEAL for general application, screw-in thread see data sheet D5-032 per DIN 3852: G 1/2 A, PN 400 design: standard connection of meas. instrument directly welded material wetted parts: stainless steel mat.-no. 1.4404/1.4435 (316L) system filling: Synthetic oil, free of silicon FD1 acc. to FDA 21 CFR 178.3570 / H1-registered DMB_787 temperature range: see below -20...+205°C

تحت الطلب

أحصل على سعر

GA2700-HY-A1433-C1050-G11-N2-T150-Z53 PA2430-F12-H1

GA2700-HY-A1433-C1050-G11-N2-T150-Z53 PA2430-F12-H1 RESISTANCE THERMOMETER MiniTherm for food/pharmaceuticals/biotechnology acc. to data sheet T4-015 measuring resistor: Pt100, tolerances per class A per DIN EN 60751 process connection: clamp connection nominal width: Tri Clamp 1" / 1 1/2", ø 50.5 mm temperature detecting element: ø 6 mm insertion length U1: 50 mm material wetted parts: stainless steel mat.-no. 1.4404 (316L) measuring resistor: 1 x Pt100, 3-wire technology, standard electrical connection: circular connector M12 x 1 (4 pins) incl. transmitter into st. steel plug housing with locking plug M12 (type PA2430) TRANSMITTER for temperature (Pt 100), programmable 0...150 °C error current if there is a sensor break 22.8 mA sensor offset: 0 °C, standard damping: 0 s, standard output signal: 4...20 mA, standard

تحت الطلب

أحصل على سعر

CC6020-A1091-H1-T110

DL4100-HY-A4007-L23-T61-W1020 DRUCKMESSUMFORMER COMPACT für Druckmittleranbau Bauform: mit Temperaturentkoppler gemäß Datenblatt D4-020-7 Ex-Schutz: ohne Drucksensor: Piezoresistiv für Überdruck Messbereich -1...9 bar, Überlastgrenze 60 bar Messgenauigkeit: Linearitätsfehler incl. Hysterese < + 0,2 % v.E. Abgleichgenauigkeit < +/- 0,2 % v.E. Ausgangssignal: 4...20 mA, 2-Leitertechnik elektrischer Anschluss: Winkelstecker nach DIN EN 175301-803-A (DIN 43650 Form A), IP 65, für Kabel ø 4-10 mm MEMBRAN-DRUCKMITTLER für Food/Pharma/Biotechnik Bauform: mit Clampanschluss gemäß Datenblatt D5-026 Prozessanschluss: nach DIN 32676 Reihe A (metrisch) für Rohre nach EN 10357, DN 25 / PN 25 Hygiene-Ausführung nach EHEDG Doc.8 und ASME BPE SF3 Oberflächenrauheit (messstoffberührte Teile) - Drehteile Ra <= 0,76μm - Membran Ra <= 0,38μm - Schweißnaht Ra <= 0,76μm Messgeräteanschluss: direkt verschweißt Mat. messstoffberührte Teile: Edelstahl W.-Nr. 1.4435 (316L) Systemfüllung: Silikonfreies Synthetiköl FD1 gemäß FDA 21 CFR 178.3570 / H1-registriert Einsatztemperaturbereich -10...+200°C Stempelung für Materialzeugnis nach EN 10204 3.1

تحت الطلب

أحصل على سعر

CC1020-A1056-H1

DL2300-A3007-L22 PRESSURE TRANSMITTER UNIVERSAL for diaphragm seal operation design: standard housing acc. to data sheet D4-029 measuring principle: piezoresistive explosion protection: without measurement: gauge pressure measuring range: 0...4 bar, overload limit 20 bar output signal: 4...20 mA, 2-wire circuit DIAPHRAGM SEAL for food / pharmaceutical / biotechnology design with coupling nut see data sheet D5-025 process connection: DIN 11851, DN 40 / PN 40 connection of meas. instrument directly screwed G 1/2 material wetted parts: stainless steel mat.-no. 1.4435 (316L) system filling: Synthetic oil, free of silicon FD1 acc. to FDA 21 CFR 178.3570 / H1-registered design temperature process -10...+140 °C

تحت الطلب

أحصل على سعر

CV4110-R70-A3066-F1-Q2-H21-M21.1-Y14-T1-T20-U9

PRESSURE TRANSMITTER PASCAL B4012-L31-T32 DD8030-D410-K1-E1-G7

تحت الطلب

أحصل على سعر

CE6120-A1060-K1014-T120-N2-H1-W1201

COMPACT PRESSURE TRANSMITTER with threaded connection see data sheet D4-020-1

تحت الطلب

أحصل على سعر

CE6120-A1060-K1010-T120-N2-H1-W1201

COMPACT PRESSURE TRANSMITTER with threaded connection see data sheet D4-020-1

تحت الطلب

أحصل على سعر

CE6120-A1054-K1014-T120-N2-H1-W1201

COMPACT PRESSURE TRANSMITTER with threaded connection see data sheet D4-020-1

تحت الطلب

أحصل على سعر

BE4200-A2092-N4200

DRUCKMESSGERÄT mit Rohrfeder und elektrischem Grenzsignalgeber, Chemieausführung gemäß Datenblatt D3-025 BE4 2 Gehäuse: NG 100 nach EN 837-1 S1 0 Ausführung: IP 65, Prozessanschluss unten 0 Ex-Schutz: ohne A2 Prozessanschluss: G 1/2 B 092 Anzeigebereich: -1...15 bar N4 elektrischer Grenzsignalgeber: Induktivkontakt mit Standard-Initiator (N) 200 Schaltfunktion: 1 x max. Öffnungskontakt elektrischer Anschluss: Anschlussstecker mit Kabelverschra

تحت الطلب

أحصل على سعر

BH4240-A92 DL4100-A4007-L23

DRUCKMESSGERÄT mit Rohrfeder für Druckmittler gemäß Datenblatt D2-029 BH4 2 Gehäuse-Nenngröße: NG 100 mit rückseitiger Ausblasvorrichtung nach EN 837-1 S1 IP 66, mit Flüssigkeitsfüllung, Prozessanschluss unten 40 A Genauigkeit: Klasse 1,0 nach EN 837-1 92 Anzeigebereich: -1...15 bar Zeiger: mit Mikroverstelleinrichtung DL MEMBRAN-DRUCKMITTLER für Food/Pharma/Biotechnik 4 Bauform: mit Clampanschluss Prozessanschluss: nach DIN 32676 Reihe A (metrisch) für Rohre nach DIN 11850, DN 25 / PN 25 100 A400 Messgeräteanschluss: direkt verschweißt 7 Material mediumberührte Teile: Edelstahl W.-Nr. 1.4435 (316L) Systemfüllung: Silikonfreies Synthetiköl FD1 gemäß FDA 21 CFR 178.3570 / H1-registri

تحت الطلب

أحصل على سعر

CX2001-A267

HIGH-TEMPERATURE-PRESSURE TRANSMITTER for high temperature application data sheet: D4-030-E1 CX2 Ex design: TÜV 02 ATEX 1971 X II 1/2G Ex ia IIC T4 Ga/Gb output signal: 4...20 mA, 2-wire technology degree of protection: IP 67 001 A measurement: gauge pressure 267 measuring range 0...1,6 MPa SPECIAL DIAPHRAGM SEAL for high temperature application connection flange: ø 90 mm, with 4 bore holes d = 13 mm and 2 dismantling screws M12 connection of meas. instrument: directly screwed G 1/2 diaphragm material: stainless steel mat.-no. 1.4435 (316L) extention length: h = 91 mm mat. sealing surface/extension stainless steel mat.-no. 1.4404 (316L) system filling: FMH1 operating temperature range: +10...+350 °C Customs-Tariff-No.: 90262020

تحت الطلب

أحصل على سعر

CB6010-A1059-H1-K1010-T420-W2673

COMPACT-DRUCKMESSUMFORMER CB6010 soll mit einem 1/2" NPT Anschluss versehen werden ("-K1030-"). Das passt nicht überein mit der angefragten Einschweißmuffe MC1000-A1, da die Muffe ein G1/2" Gewinde hat. Daher wurde auch der CB6010 mit einem G1/2" Anschluss versehen ("-K1010-").

تحت الطلب

أحصل على سعر

FU2430-A2160-D1207-F10996-G4-K39-L4630-R11-W4020

GAS EXPANSION THERMOMETER with switch function and capillary acc. to data sheet T3-029 FU 2 case: DN 100 43 case design: IP 66, bottom connection 0 explosion protection: without A2 accuracy class: see data sheet 160 nominal range: -50...+50°C D12 process connection: shanks rotating 07 nominal width: G 1/2 F10 temperature detecting element: ø 10 mm 996 insertion length L1 (mm): 198 G4 mounting: with wall bracket, aluminium K3 capillary: material stainless steel 9 length of capillary [m]: 5,00 L4 switch function: magnetic snap contact switch function: change over contact, 1. contact falling switched,2. contact rising switched 630 R11 window: Macrolon electrical connection: connection plug with cable gland M20 x 1.5 and removable test cover, mat. Macrolon W4020 ADDITIONAL DESIGN: marking (adhesive label), see below

تحت الطلب

أحصل على سعر

FU2430-A2524-D1207-F10996-G4-K39-L4630-R11-W4020

FU 2 case: DN 100 43 case design: IP 66, bottom connection 0 explosion protection: without A2 accuracy class: see data sheet 524 nominal range: 0...+100°C D12 process connection: shanks rotating 07 nominal width: G 1/2 F10 temperature detecting element: ø 10 mm 996 insertion length L1 (mm): 198 G4 mounting: with wall bracket, aluminium K3 capillary: material stainless steel 9 length of capillary [m]: 5,00 L4 switch function: magnetic snap contact switch function: change over contact, 1. contact falling switched,2. contact rising switched 630 R11 window: Macrolon electrical connection: connection plug with cable gland M20 x 1.5 and removable test cover, mat. Macrolon W4020 ADDITIONAL DESIGN: marking (adhesive label), see below

تحت الطلب

أحصل على سعر

FU2430-A2544-D1207-F10996-G4-K39-L4630-R11-W4020

GAS EXPANSION THERMOMETER with switch function and capillary acc. to data sheet T3-029 FU 2 case: DN 100 43 case design: IP 66, bottom connection 0 explosion protection: without A2 accuracy class: see data sheet 544 nominal range: 0...+160°C D12 process connection: shanks rotating 07 nominal width: G 1/2 F10 temperature detecting element: ø 10 mm 996 insertion length L1 (mm): 198 G4 mounting: with wall bracket, aluminium K3 capillary: material stainless steel 9 length of capillary [m]: 5,00 L4 switch function: magnetic snap contact switch function: change over contact, 1. contact falling switched,2. contact rising switched 630 R11 window: Macrolon electrical connection: connection plug with cable gland M20 x 1.5 and removable test cover, mat. Macrolon W4020 ADDITIONAL DESIGN: marking (adhesive label), see below

تحت الطلب

أحصل على سعر

FU2430-A2999-D1207-F10996-G4-K39-L4630-R11-W4020

GAS EXPANSION THERMOMETER with switch function and capillary acc. to data sheet T3-029 FU 2 case: DN 100 43 case design: IP 66, bottom connection 0 explosion protection: without A2 accuracy class: see data sheet 999 nominal range: see below -100...+100°C D12 process connection: shanks rotating 07 nominal width: G 1/2 F10 temperature detecting element: ø 10 mm 996 insertion length L1 (mm): 198 G4 mounting: with wall bracket, aluminium K3 capillary: material stainless steel 9 length of capillary [m]: 5,00 L4 switch function: magnetic snap contact switch function: change over contact, 1. contact falling switched,2. contact rising switched 630 R11 window: Macrolon electrical connection: connection plug with cable gland M20 x 1.5 and removable test cover, mat. Macrolon W4020 ADDITIONAL DESIGN: marking (adhesive label), see below

تحت الطلب

أحصل على سعر

BA4200-A9265-W4005-W4020

BOURDON TUBE PRESSURE GAUGE in chemical design 2 case: DN 100 per EN 837-1 S1 00 case design: IP 65, process connection bottom acc. to data sheet D2-026 A9 process connection see below R 3/8B taper 265 nominal range: 0...0.6 MPa W4005 ADDITIONAL DESIGN: free of oil and grease for oxygen applications W4020 ADDITIONAL DESIGN: marking (adhesive label), see below

تحت الطلب

أحصل على سعر

CC6020-A1091-H1-T410-W2002

DL4100-HY-A4007-L23-T61-W1020 PRESSURE TRANSMITTER COMPACT for diaphragm seal operation

تحت الطلب

أحصل على سعر

BH4250-A91-W4020-W1201-W2673 DL4100-HY-A4007-L22-W4066-W1020

Druckmessumformer Labom BH4250-A91-W4020-W1201-W2673-DL4100-HY-A4007-L22-W4066-W102

تحت الطلب

أحصل على سعر

BA5210-A2060-W2673

Labom Manometer BA5210-A2060

تحت الطلب

أحصل على سعر

BA5220-A2092-W1201-W2673

Labom Manometer BA5220-A2092-W1201-W2673

تحت الطلب

أحصل على سعر

BA5220-A2091-W1201-W2673

Labom Manometer BA5220-A2091-W1201-W2673

تحت الطلب

أحصل على سعر

BH4240-A90-W1201-W2673 DL4300-HY-A4007-L22-W4066-W1020

Druckmessumformer Labom BH4240-A90-W1201-W2673-DL4300-HY-A4007-L22-W4066-W1020

تحت الطلب

أحصل على سعر

BH4200-A92-W1201-W2673 DL4100-HY-A4007-L22-W4066-W1020

Druckmessumformer Labom BH4200-A92-W2002-DL4100-HY-A4007-L22-W4066-W1020

تحت الطلب

أحصل على سعر

CC6020-A1091-H1-T410-W1201-W2673 DL4100-HY-A4007-L23-T61-W4066-W1020

Druckmessumformer Labom COMPACT CC6020-A1091-H1-T410-W1201-DL4100-HY-A4007-L23-T99-W4066-W1020

تحت الطلب

أحصل على سعر

GA2700-HY-A1413-C1150-G11-N2-T150-Z52-W1201-W2673 PA2430-F12-H1

Temperatursensor Labom GA2700-HY-A1413-C1150-G11-N2-T150-Z52-W1201-PA2430-F12-H1

تحت الطلب

أحصل على سعر

GA2730-A10-C3998-M2-N2-T150-Z52-W4999-W1201 HP1200-HY-A25-B1412-E2050-G11-W1020 PA2430-F12-H1

تحت الطلب

أحصل على سعر

GA2500-A2310121-B40-D2-M22-N2-T11-Z1-W1201-W2673 PA2100-F12-H1

Temperatur-Sensor PT 100 Labom GA2500-A2310121-B40-D2-M22-N2-T11-Z1-W1201-W2673-PA2100-F12-H1

تحت الطلب

أحصل على سعر

BE4220-A2092-L4120-W2673

Labom Manometer BE4220-A2092-L4120

تحت الطلب

أحصل على سعر

1 2 3 4 5 6 7

يحتوي الموقع على جزء صغير فقط من عناصر الكتالوج LABOM.

إذا لم تعثر على المقالة التي تحتاجها ، أرسل طلبًا إلى البريد الإلكتروني [email protected] وسنرسل لك بالتأكيد عرضًا تجاريًا.

هنا يمكنك شراء منتجات من ماركات أخرى

ارسل طلب

سنتواصل معك ونجيب على جميع أسئلتك